HOW TO WIRE PID FOR SINGLE OR MULTIPLE HEATING ELEMENTS | RE-EDITED & UPDATED

Is this for 240 volts??

Is it for multi heaters with more than 5, the diagram is the same???

Nt 72 e

Great video, thank you. Where would a dry cut-off float switch fit in?

How to add timer controler on this diagram?

Thanks this was very helpful, I will need to run 2 elements for my project.

Thanks

The mc70q is in Celsius so do you know a comparable or same hook up for one that shows temps in Fahrenheit?🤔
Also if you needed let’s say 25+ amps one could swap out the on/of breaker switch to a higher value breaker since the relay is rated at 40amp correct? More concerned about a pid not in Celsius but one in Fahrenheit is needed any ideas on a pid for such?

THX man, It Is so clear to understan, bye from Italy...

Thanks for the video, what about the ground line? Do you simply splice the ground from the input power like directly to the ground of the element?

As per my above comment, aren’t 2elements connected to really act as one long element?

Question: why is it necessary with two elements to use 2 SSR s. Rather than one 40 amp SSR?

Each resistor bar uses 1 SSR, right (2 thermistor bars is to use 2 ssr)

How to
Alam volt

This video is awesome, I'm going to be converting a dial controlled kiln into a pid controlled kiln - really helped me understand what goes where, and WHY!

This is the video I was looking for, I have a question, if you can receive it and give an answer: I have a 2500W heating element, can I connect to this temperature controller? Thank you.

I want to add PID temperature control to my 240VAC instant hot water heater. What controller and sensor would you recommend?
Is there such a thing as proportional heater control?
A heater controller that factors in flow rate?

Thank you for the lucid presentation on the PID connection. God bless !
From Addis Ababa, Ethiopia

great job bro. helpful

Great Video my friend. I have a 12v alarm busser so I assume I will need to power it by running a 12+ to pin 2 and pin 1 to red on the busser , then busser black wire to a 12v -black source.

What if you only want 1 switch and 2 heating elements? Can you have two wires going to the - and + terminals of the SSR?

I would like to put 1 pid with 3 ssr for 3 element of 3000 watt (240v) each, can it be possible with only one pid? The switch on the ssr line doesn't need to be a big one(120v) they only cut one line, like you said, its only a switch for a contact NO on the ssr, the control will be done on the pid, right?

Very well explained bro....appreciate the afforts..

The best explanation so far !!!!!

Excellent video but I want also to send the measured temperatures to excel in my notebook every 5 seconds. I suppose a small PLC with USB output (Raspberry Pi?) will be required but I am not sure about the configuration and recommended wiring. Do you have a video or suggestions about that? Many thanks

The way you explained things are very easy and clear at least learners don't have a hard time to understand, we appreciate your video, it's full of knowledge, keep it up brother

This is exactly what I need but I also want to add a timer . Do you have a video with a timer as well? Thanks!!

second heat element the #11 goes to the positive of the second SWITCH, not relay, the graphic is correct but you must said it by mistake. great video

With 240v tho there should be two hot leads from plug how do I wire this ? Plz help . Your video is super helpful but I am stuck on this .

Thank you I had a slight understanding from other videos but yours helped me really understand I appreciate you

I followed the diagram but the coils arnt heating up

Can you tell me the link to get the alarm bell

Hi, i buy an Rex-700 with 4-20mA Output to connect these Output to an Voltage Regulator SSR-40A with an 4-20mA Input. The Rex-C handle the SSR on and off, but not Power up and down like i hope. I cant find the function in settings. Can you help?

Thank you from india.... Very usefull bro thanks ആണ് loat

Can that same wiring diagram be used on a powdercoating oven

Sir i have question , how about the wiring diagram when using 8 heating ??

Sir i have question , how about the wiring diagram when using 8 heating ??

You are the first genius video i watch of this subject
If i have 10 heating element do i need 10 ssr

👍🇦🇿

Sir wanna ask some help,, i was planning on building my self a curing oven for powder coating,, with 2 heating element, with 3000w each,, how much of an amps should i go with the specs??

HOW TO PROGRAM PLEASE Make a video

Is the Pids 220v?

I just want to know why all the comments are just different versions of the exact same thing LOL there are many videos like this has concisely as this. Makes me feel like they are purchased comments

How do you break in to the blue wire for example or do you mean you go from pin 8 to the element or am I just missing something, thank you

Very amazing video, please make the electric convection oven video with three phase supply three heaters in series, and with fan forward and reverse.

This is exactly what I was looking for. Thanks for the video!!

This is great .... thanks

Love your video. I am in Texas, USA. Here we have 240 volts composed of two 120 volt circuits 120° out of phase. I am connecting the heating elements from an old Wall Oven. What mods are required of this circuit, if any? Thanks. Tim

Thanks so much, your effort is appreciated!

can you make an example of how to wire 2 PID rex c100 with 2 heating elements, mcb, switch on / off