How to change spark plug on LEXUS RX400h 2 (XU30) [TUTORIAL AUTODOC]

you did,t
show main thing how to unscrew manuford back 3 bolts😂
thansk to show easyer ones😂😂

Great video, my only suggestion would be to have the cameraman zoom in and zoom out more often on some of those areas that are in deep. It just helps to figure out exactly what was being worked on. I know he did it once or twice, which I thought was greatand appreciate that but he did it for all areas that were in deep. It would really help. Super thanks again.

26 Nm torque broke the spark plug

The hardest screws you blow through it in 15-20 sec… how do you get the the 2 screws in the back of the intake manifold?

Great video. Professional. I wonder what the dealer charges for this service. It's a pretty big ordeal.

You forgot to show how to remove the WHOLE WIPER ASSEMBLY to remove the 2 12mm bolts on the back of the Air Intake. It takes about an extra 2 hours and a lot of scars to get there. It's funny how you skip that part in just 2 seconds! The rest was Super helpful.

What is it your doing from underneath the car at the end of video? Thanks

Wow! Thanks for such a detailed and informative video on replacing the spark plugs! The disassembly and reassembly was very helpful and clearly shown and documented! I’m going to watch the video over and over again until I feel comfortable to start it on a diy project. Thanks again Auto Doc.

Are you UK based and where is this workshop? Need lots of work on my Rx400h from a reputable and knowledgeable place like you guys

I replaced my back coils and it worked out fine. Thank you for the video. My plugs have been replaced at one time and the last person did not put the screws back on the pack part of the manifold so it made it easy to take that off.

I know this will probably never be seen. However, am I supposed to change the throttle body gasket and intake gasket? I figured I would ask since I didn’t see them changed and rubber gaskets get old and hard with age. Thank you. Absolutely great video!!!

Very good good live 1.👍

Very helpful this video clip 👌,
I would like to know what you do or what you disconnect when you go under the car ,it was not clear ,please explain.
Thank you very much.

Can any coil go in any hole

Humm... it didn't make the triangle red light go away....:(

I came here to scan the video for the part where they get at the rear intake manifold support brackets and they literally skipped only that part!

Oh man so the intake has to come off and I have to watch this video like 3 times

Thanks for the detailed info.

this is not a real portrayal of how its done, there was not a single *&%^ in the whole thing

I like this video, It would be nice to hear basic narrative while you work. Also I am replacing the spark plugs at a longer interval, 140K mi, Because with the new irridium plugs they always look so great when they come out. FYI the timing belt and water pump were done at 90K. With this video I will be doing this job today and.... Thank you so much for your contribution!!!!

Tough job for the newer model cars! Great video.

Wth are you doing

How we should know that the spark plugs need to be changed? is there any symptoms on the engine function that should know that the spark plug is dirty or need to be changed?

Please, show how to replace fuel pump on this vehicle.

Hi, Did you unplug the 12V battery? Please advise. thanks

Great video. Everything anybody would need to know in order to do this job. This explains why my Lexus dealer charges $690 to do this! Also explains why I’m not going to tackle it myself. I could... Especially with this video... but I’m just NOT. Thanks for the help!

You didn't show how you removed the 14mm and 12mm fasteners at the back of the intake plenum... 😂

To break the two back bracket bolts, you'll need a long breaker bar and angle it on a small 12mm wrench. You cannot get enough leverage otherwise.

Too bad that the video did not show when the technician get down below to get the 3 screw from the back of the air intake manifold as it is tight spot. We do not know how can them be remove. I did all the thing from the top but find out that it still sticking as the 3 screw can not remove. it should be explained to the viewers that the vehicle need to be lift up high to get access instead he only point out the spots. I like all other video and they are helpfull. But this one I have problem with it.

Why is there no region for the United States on the app? Love his channel thou because im a do it yourself kind of person

FANTASTIC ! I HAVE LEARNED A LOT.

Next time, is it possible to show me how you took off the 2 bolts from the back of the intake manifold? That's the most tricky part and you left it out. Thanks.

Why did you not replace the coils. Or clean the EGR valve. Once going back into that area I would never want to have to go back into it again

👍

I noticed you didnt go back under the car to install that bracket bolt in the back of the intake.

can you do a rx400h waterpump and timing belt?

extremely thank you for the video

Good 👍👍👍👍👍👍👍

Excellant work.