Комментарии:
What are you doing with the 3 speed over drive?
ОтветитьI have never seen Dan check the torque converter to flywheel clearance, and that should always be done, and shimmed if necessary.
ОтветитьYou're killing me it's not that hard to put the transmission in after the motors installed
ОтветитьHi Dan and Daniel just want to say thx for t-shirt,it arrived two days ago,I heard you did a little sneaky intel to get my address,love the content and keep up the good work
ОтветитьI love that NOMAD!!!! One day a while back, I arrived at my friends house just in time to stop his son from trying to bolt a 350 tranny up to a 283 with the converter bolted to the flex plate! Saved him a lot of grief!! LOL!!!
ОтветитьBy the way Dan the nomads ain't worth that much just so you know that😊
ОтветитьYou had me on the edge of my seat when it was not going in Dan. I thought you were going to have to take the rad core support out to get it in there!
Ответитьwith more power more brakes..
ОтветитьThis is going to be one REALLY SWEET ride and PERFECT for HR Power Tour!
ОтветитьLove that Nomad.
ОтветитьDan, a couple of ideas. Shorten the chain. When you get the trans attached to the engine, you should be able to spin the torque converter. Really enjoy you and Dannie.
ОтветитьYou know Dannie enjoyed her vacation to the islands without any mistreatment by Dan 😂
ОтветитьCool thanks again for letting us know what ❤❤
ОтветитьI'm surprised that Mortske hasn't sought asylum in Canuckistan - he must be at risk of deportation to El Salvador as a felon.
ОтветитьAlso why are torque converters such a pain in the ass to put in?
ОтветитьAwesome but T.M.I. on the underwear!
ОтветитьGreat move Dan rebuilding the engines for reliability
Ответить👍🏻🍻
ОтветитьGood old fashioned blown small block. Just meant to be in the fender Wells of a 55. Looking good man. Should be a blast to drive.
ОтветитьScrew that DAN sleep when your dead... keep on trucking.... then youll enjoy time off even more...if you know you know...yall are doing a fine job
ОтветитьRad support removal might have helped.
ОтветитьDan here... Mr. Goodwrench...
ОтветитьAusome Dan gona bee bad ass
ОтветитьPut tranny in from underneath. You have a hoist man. Drop motor straight down, no trans on and then install trans later. Easier.
Also why not put hoist under the ceiling hoist you have and use it . 😊
No fender covers???????dude your gonna mess up that nice paint
Ответитьso what going in the so madd nomad
ОтветитьThanks for the video you 2.
ОтветитьDan is so mean to you Dani😂😂
ОтветитьGonna be one badass combination 👍👊
ОтветитьThat nomad in mint condition is worth 100,000 us dollars
ОтветитьDan Math: [Measures the transmission for center], "17 and 17 1/8" - [shifts the transmission and re-mesures] "17 and 17, we'll call that good". That eighth inch just evaporated into the ether or the car got narrower...lmao
(Yes I know an eight doesn't matter but the Dan math is priceless.)
just put MSD , small gap and you wont have any problems.
ОтветитьThere's better legs in a bucket of drumsticks
Ответить20k Canadian.🤔 So, about $1,500 US then??😂😂
ОтветитьDD SPEED SHOP
DD SPEED SHOP
DD SPEED SHOP
I have the all black " garage hack" shirt, thank u so much, I feel important now. Lol lol
ОтветитьGlad to see the nice Nomad getting some love. It should be a blast on Power Tour.
ОтветитьIt's great to see them building a "nice" car for them to daily drive. God forbid Dan cuts a hole in the Hood for a scoop, and ruins the look of this classic. It would be nice to see it as a civilized street rod with a quiet exhaust. Something that wouldn't wear you out to drive long distances. If he wants to go "nasty" that's what his other Nomad is for.
ОтветитьGlad you’re not going to cut the hood for the blower.
ОтветитьNomad is going to be a badass driver.
ОтветитьTo counter weight my cherry picker I bought a used weight bar and plates. Cut the threaded ends off bar and welded them to the sides of the upright. Probably where you put transmission would've been better though. I think I paid $45. Tractor wheel weights or nose weights work good too. Drill engine hoist and put rivnuts in to bolt weight down.
ОтветитьWere those the heads out from under Mur's house ??????? Please find a desent hood for it , it makes me start twiching every time i see it !!
ОтветитьThat's going nicely 👌 ❤🎉
ОтветитьSo now she has a blower is it a "Blowmad?"😂😂👌
Ответить👍👍👍
ОтветитьThank goodness we don't have to look at that POS Monte Carlo again! 😅😂
ОтветитьDan. Take it easier on Dannie, my friend. It comes out too hard. Also, I unsubscribed from Tom and Mutt a while back. Mortske Repair no more! 🇨🇦
Ответить