Комментарии:
I am sorry but your website doesn't work, may you can help, I am looking for a volume control with switch that has 5 prongs to connect to surface mount on side of board I think it was 80K, it is for Creative Labs Inspire 6600 6.1 Computer Speakers, if you have it please let me know. Thanks,
ОтветитьThis is zero help. I dont have a chassis??? I have a lightbulb. Which is NEGATIVE and POSITIVE??
ОтветитьVery vague
Ответитьshafts and knobs ftw!
Ответитьi only clicked because shes cute
ОтветитьHow to wire a three wire dimmer to two wires in the wall
Ответить"Wiring a potentiometer is a very straight forward process" ...me: cries
ОтветитьSodder ? What is "sodder" ?
Ответитьwhy no one is doing a how to wire a sliding potentiometer ,,i have a 3 pin one can you tell me which wire goes where ,,,thanks
ОтветитьI still don't understand where the ends of the wires go to and how they connect to a speaker or a battery
Ответитьthank you!! what about 8-pin pots though? (those with an on/off switch)
ОтветитьOh my God, it depends on what you want to use it for, and NO you cannot put so much voltage or current through them, they will burn out, also don't set your multimeter to volts...lol, it needs to be set to resistance. to test what resistance it is if it doesn't state it then connect the multimeter to tabs 1 & 3, to use it as a simple volume you can connect 1 & 2 together only leaving 3 alone, now put the multimeter to 1 & 3( as 2 is connected to 1) and turn it, you will then see the resistance drop as you go higher.
ОтветитьWhat a hideous noise to kick off a video with.
ОтветитьMan ur smart
ОтветитьDamn she's sexy.
ОтветитьIt's wrong to have a pretty woman as teacher, nobody listens and learns anything...
Ответитьwhat is the difference between type A and type B potentiometers ?
ОтветитьI just watch another video and 1 2 and 3 like you said was positive1 signal2 and groung 3
ОтветитьHwo to determine the terminal of rotary potentiometer
ОтветитьI like hearing you say shaft
ОтветитьSurely she meant ohmmeter?
ОтветитьShe almost kept a straight face the entire time. Well done.
ОтветитьShe keeps from laughing so much it's great
ОтветитьI came to see comments about shafts and knobs, I'm quite disappointed.
ОтветитьThanks, Ms. Practiced Hand Gesture!
Ответить"How to wire a potentiometer." .........Better yet, find another source of information.
ОтветитьSo you set that nice Fluke Meter to VDC to measure the Resistance change of the Potentiometer? Got it.
ОтветитьNice video.... and nice nails :-)
ОтветитьWould this work for controlling the speed of a dc motor im running about 33volts with no load
Ответитьlooks like katie has some competition cuz she got that BOMB
ОтветитьThis is so sweet and perfect video. Also very good in managing and editing , Thank You
ОтветитьYou only need 2 leads for hot signal control, granted your inputs ground themselves when nothing is connected. The third pin is most used for audio ( non dc electrical control. Never attach anything to this pin if controlling voltage as you will cause a short to ground. So 3 pins for audio and 2 pins for voltage control.
ОтветитьThank you
Ответитьturn that shaft now.
ОтветитьI looked at about 25 wiring diagrams of potentiometer terminals. With the potentiometer positioned the way you have it. Some had ground and power/input terminals reversed. How can you tell which way a potentiometer is structured? I thought they were all the same: Ground Signal/Output Power/ VCC. But judging from the wiring diagrams they are not?
ОтветитьJust curious. Some pronounce it potentiooooometer and some potentiomeeeeter. Is it US / UK or just two ways of saying it?
ОтветитьSweet, that's exactly what I needed to know! Thanks!
Ответить