Solving MY BIGGEST Problem with the DJI O3

I have same issue , took it apart last night and didn’t notice any play , but i ll adding súper glue to it for sure

Which antenna connector goes to which terminal on the unit? Does it make a difference?

I just tested this with no luck. Seems just as bad even with the glue applied and the PWM changed.

Dji probably knew about this issue from the beginning. The amount of money people are paying for this product it should be fixed at the factory and recall the ones that are defective.

how do you record with the o3 air unit? i insert sd card to both DJI O3 air unit and DJI goggles 2, but the O3 air unit did not record anything.

So you did DJI repair centers job for them. They now owe you the hourly fee they pay to those workers for making your own repair. This is unacceptable from DJI to mass produce the 03 air unit and its not sealed for condensation and the cameras come brand new wiggling lile this? Unacceptable. Glad you were able to tinker with it and make it work for you! I think DJI expected a bunch of ppl building their own drone would think they did something wrong on the build themselves. Here it's all their fault.

For what you’re paying for this stuff you should not have to do all this modification. This is fuckin nuts. And dear God I can’t believe how bad the low light is on this camera. I mean what on earth DJI. How can you make it this difficult for me to decide on whether or not I should buy this shite.

I had same issue from the beginning, but after changing PVM to 96 KHZ it helped. Just realised that once i dive with throttle 0, footage in goggles shake (and once throttle is back on, problem - gone). While replaying video from air unit on the computer, no shake on the dive. Maybe any ideas? I mounted camera in tpu cage, slided it in without any screws. Maybe it is the problem? But why it occurs only on the dive. Any adeas? Thanks!

Is this for the recorded video or for the live feed? My live feed does not shake but my rocksteady video had a little shake on throttle blips.

Can you please show a night flight?? just to see what is possible?? Most people say that it sucks!!

I had the same issue. Your solution works perfectly in my case. However I didn't apt glue, simply I tighten more the 4 screws that attach the lens to the body and put a little bit of double side tape in the back of the lens in order to the back body press firmly the lens insidithe main body.Thsnks a lot for share this with all!!!

Glad I could help! Thanks for the credit!

I’ll be doing this for sure! Thanks!

HI Darren, I have the same issue on the onboard footage, somehow on the dvr I don´t have the issue - what do you think? is it the same problem as in yours?

That's awesome! Thanks! I was wondering... Did you get the PWM to 24khz again?

your drone has to be almost perfect for the 03 every little vibration or dsync shows up really annoying tpu mounts and tpu washers seems to help

Just realized that you are DazBot! How's the o3? I'm planning to put it on an open racer build, is it durable enough to withstand minor to major crashes? 🙏

Yep. This happens with like half of my o3 cameras. The other half are perfect.

Thanks! Is this the "pwm frequency low" settting for the 48 khz ??

Hi, thank Bro fix GPS is another problem 🤔🤔

The problem is crappy frame design more than anything. Replacing the whole mount with TPU would have solved the issue.

Is it the 2fiddy 5inch right? Props aren't in view cause you are in wide mode and not in ultrawide right?

had a very small crash and then i had the same problem like you, i hope i can fix it. thank you.

I have 3 units of o3, none of them have this issue😅

Wow that’s a hectic fix! Havnt heard of that issue before? Mine was having heaps of problems but a new 3D cam mount fixed it thankfully.

on my o3 have no Jello

Rather than pull your hair out trying to fix an obvious defect, why didn't you just return it to where you purchased or sent to DJI for replacement?

What if you now go back to 24kHz? Will it came back?

Hello everyone im gonna fix my camera, whats the best glue or alternative i could buy ?

Hey
I wondering if somebody could give me advice how to adjust focus on o3 camera. Unfortunately I have focus only in the center rest is blurry 😅

I just have the same Issue and will try your Solution.
Can you tell me how to change the PWM Setting? I am really new to this Topics^^
I looked for it in Betaflight but could not find this Settings.

My issue was the PWM frequency, went away when I changed it to 48 kHz. Was not noticible at all in the unstabilized footage. If it helps anyone, my issue presented itself as "jiggling" in the roll axis when stabilizing the footage in Gyroflow. This was on my Nazgul Evoque F5 V2 BNF.

How can I change to the 48 khz? Does that work in Betaflight or how do you do that?

Super glue bad idea round optics, it can seep and leave a residue into the smallest gaps,

So when you tried to wiggle the camera, once you disassembled it, did the camera feel loose? Or you just put superglue in there anyway?

I did all of the suggested solutions, glue on lens, 48khz pwm, good frame and props, camera isolation with dampners, and I still get horrible jello with my Cinebot 30 and dji 03 air unit. HELP

This doesn’t look like 03 , the footage is horribly pixelated and blurred out, it seems to me you’ve got more problems than just jittery camera 🙄

Hello Darren, i have a question, if buy an 03 AU and install it in my own quad platform with GPS, will i have to connect my goggles 2 to GPS in order to arm ? Thank you

Thanks!!! Subbed

i will try it on walksnail pro camera

Thanks a lot !! I did the 48khz esc + glue on cam and now.... No more jitter/jello !!! What a relief 🎉

I'm just surprised that DJI hasn't fixed this between batches during manufacturing, even if it was to just add the adhesive like you did during assembly!

si es asi el problema ,ES UN MAL CONTROL DE CALIDAD DE DJI...lo cual es preocupante...

If so, the problem IS BAD QUALITY CONTROL BY DJI...which is worrying...

darren problem is in live video and/or rec vide0?.thx for video bro.

For that price there should be no problems to fix with glue or by yourself, what a shame dji

Amazing i crash my nazgul change camera i have a feeling is the same issue thanks

that thumbnail photo was hilarious lol